Hand lock instructions

- Jul 26, 2018-

Hand lock instructions:

The hand lock is divided into a split lock, a body lock, and a three pole quick lock. The product has many materials, including zinc alloy, stainless steel, copper and aluminum alloy. Indoor door locks on style are European, Chinese, modern simplicity of the three, in order to match the various styles of furniture, the shape of the hand, color is more diverse, colorful. Product safety is relatively good, often used in door, door. Housing, office buildings, hotels and so on are available. After electroplating and electrostatic spray paint, the handle has the effect of abrasion resistance and corrosion protection. In addition to the decoration style, it should be able to bear greater tension, and the general handle should be able to bear more than 6 kilograms of tension.


Handle Lock material zinc alloy, copper, aluminum, stainless steel, plastic style European, Chinese, modern simplified classification lock, joint lock, three bar fast lock


Brief introduction:

The hand lock is divided into a split lock, a body lock, and a three pole quick lock.

There are three kinds of indoor door locks: European style, Chinese style and modern simplicity.

The product has many materials, including zinc alloy, stainless steel, copper and aluminum alloy.

Product safety is relatively good, often used in door, door.

Housing, office buildings, hotels and so on are available.


Commonly used specifications:

The most commonly used lock core two kinds of 4 specifications MM: big 70, small 70, big 68, small 68, generally have aluminum alloy, zinc alloy, copper as the material lock core.


Making materials and characteristics:

Hand lock can be divided into space aluminum, stainless steel, copper die-casting, zinc alloy several, space aluminum, stainless steel materials advanced, through surface processing, glossy bright, soft hand, though sweat, moisture corrosion is not easy to fade and rust. Die casting copper hand lock is more thick, moderate price, and the low quality of zinc alloy hand lock is easier to break, because the zinc alloy hand lock surface copper plating, purchase and copper die-casting locking hand lock is not easy to distinguish, can use setback knife in two kinds of lock bottom plate repeatedly setback, pan brass for copper die-casting lock, pan pan, pan pan, pan The silver white is a zinc alloy hand lock.


Lock installation:

1, cut out the installation paper plan attached to the appropriate height of the door (the center of the hole is about 1 meters away from the ground).


2. According to the left and right door opening, adjust the inclined plane of the inclined tongue to face the door, then lock the lock body into the lock hole and fasten it with self tapping screws.


3. Insert the lock into a beforehand slot, fix the lock with a screw, and insert the square core into the square hole of the lock, then insert the front and back side holes into the square core, and twist the two fastening screws on the inner panel (temporarily not tighten), and pass the lock core from the door to the door through the lock hole, and fasten the lock core and the lock with a lock core. Tighten the 2 fastening screws on the inner panel.


4. Chisel box holes and buttoned support sockets shall be chiseled out at the corresponding positions of the doorframe. The buckle box and the buckle plate should be installed and fastened with self tapping screws.


Daily maintenance editor´╝Ü

1, the newly decorated house contains a lot of corrosive gases, especially the paint on the wooden door will send out formaldehyde and other corrosion gases, which will seriously affect the service life of the lock and even corrode the lock. It should be ventilated and kept dry in the room.


2. Remove dust and dirt on the handle lock surface. Dry cloth should be used to wipe the handle and lock body. Avoid using wet cloth or cleaning with acid or alkaline detergent.


3, hold the lock in the daily switch door process, it is best to hold the hand to screw the lock tongue into the lock body, after closing the door and then loosing the hand, do not force the door, otherwise it will reduce the service life.


4, when the lock is used for a period of time, there may be a phenomenon of unsmooth opening. Do not drop ordinary lubricating oil or oil into the lock core, and use professional lubricating oil to open the lock several times again and again.